Part No. 114202 Rev. ANovember 1996 Installing an Expansion Module in a BayStack ARN Router
114202 Rev. A xi Figures Figure 1-1. ARN Power Switch (Off) and Power Cables ...1-2Figure 1-2. Loosening th
114202 Rev. A xiii Tables Table 1-1. Boot Status LEDs ...1-16Table 1-
114202 Rev. A xv About This Guide If you are responsible for installing Bay Networks™ hardware, read this guide to learn how to install any of the f
Installing an Expansion Module in a BayStack ARN Routerxvi 114202 Rev. A Acronyms AUI Attachment Unit InterfaceSTP shielded twisted-pairUTP unshielde
114202 Rev. A xvii Technical Support and Online Services To ensure comprehensive network support to our customers and partners worldwide, Bay Networ
Installing an Expansion Module in a BayStack ARN Routerxviii 114202 Rev. A Bay Networks Customer Service If you purchased your Bay Networks product
Technical Support and Online Services 114202 Rev. A xix Bay Networks Information Services Bay Networks Information Services provide up-to-date suppo
ii 114202 Rev. A 4401 Great America Parkway 8 Federal StreetSanta Clara, CA 95054 Billerica, MA 01821 Copyright © 1988–1996 Bay Networks, Inc. All ri
Installing an Expansion Module in a BayStack ARN Routerxx 114202 Rev. A Support Source CD This CD-ROM -- sent quarterly to all contracted customers -
Technical Support and Online Services 114202 Rev. A xxi InfoFACTS InfoFACTS is the Bay Networks free 24-hour fax-on-demand service. This automated s
114202 Rev. A 1-1 Chapter 1Installing the Expansion Module Complete the steps in this chapter to install any of the following expansion modules in a
Installing an Expansion Module in a BayStack ARN Router1-2 114202 Rev. A Opening the ARN To open the enclosure and expose the base module: 1. Be sure
Installing the Expansion Module 114202 Rev. A 1-3 Figure 1-2. Loosening the Captive Screws 8. Holding the ARN front panel so it does not move, slide
Installing an Expansion Module in a BayStack ARN Router1-4 114202 Rev. A The antistatic wrist strap directs the discharge of static electricity from
Installing the Expansion Module114202 Rev. A 1-5 Figure 1-5. Removing the Blank Panel From the Expansion Module Slot3.With the locking tabs clear of t
Installing an Expansion Module in a BayStack ARN Router1-6 114202 Rev. A4. Set the filler panel aside.To operate the ARN without the expansion module i
Installing the Expansion Module114202 Rev. A 1-7 2.Disconnect the power cable from its connector on the expansion module (refer to Figure 1-6).Pull up
114202 Rev. A iii Electromagnetic Emissions Meets requirements of:FCC Part 15, Class AEN 55 022 (CISPR 22:1985), Class A <and Class B>VCCI Cl
Installing an Expansion Module in a BayStack ARN Router1-8 114202 Rev. A6. Place the removed expansion module in an antistatic bag.7. Proceed to the n
Installing the Expansion Module114202 Rev. A 1-9 2.Insert the module’s interface connector panel into the front panel expansion slot (Figure 1-9).To c
Installing an Expansion Module in a BayStack ARN Router1-10 114202 Rev. AFigure 1-10. Inserting the Expansion Module4.Press the module all the way for
Installing the Expansion Module114202 Rev. A 1-11 Figure 1-11. Attaching the Power Cable and Securing the Expansion ModuleClosing the ARNTo replace th
Installing an Expansion Module in a BayStack ARN Router1-12 114202 Rev. AFigure 1-12. Replacing the ARN CoverARN0020ABayStack Advanced Remote NodeRLSD
Installing the Expansion Module114202 Rev. A 1-13 Connecting CablesTo reconnect the ARN:1. Reconnect any console or network cables that you disconnect
Installing an Expansion Module in a BayStack ARN Router 1-14 114202 Rev. A Figure 1-14. Token Ring CablesARN0075ACOM3 COM4 COM5UD DD B1B2RLSDRunBootF
Installing the Expansion Module114202 Rev. A 1-15 Figure 1-15. Serial Cables3.Plug in the power cord and, if applicable, redundant power supply cable.
Installing an Expansion Module in a BayStack ARN Router1-16 114202 Rev. AFigure 1-16. ARN Base Module Diagnostic LEDsWhen you power on the ARN, the fo
Installing the Expansion Module114202 Rev. A 1-17 6.After completing the diagnostic testing procedure, the boot process begins. The Run and Boot LEDs
iv 114202 Rev. A Canada Requirements Only (continued) D. O. C. Explanatory Notes: Equipment Attachment Limitations The Canadian Department of Commu
Installing an Expansion Module in a BayStack ARN Router1-18 114202 Rev. A• Modifying Software Images for Routers for information about changing the ro
114202 Rev. A v Canada Requirements Only (continued) Canadian Department of Communications Radio Interference Regulations This digital apparatus (
vi 114202 Rev. A Bay Networks Software License This Software License shall govern the licensing of all software provided to licensee by Bay Networks
114202 Rev. A vii Bay Networks Software License (continued) 9. Licensee shall not reverse assemble, reverse compile, or in any way reverse enginee
114202 Rev. A ix Contents About This Guide Before You Begin ......................
Comments to this Manuals