Avaya BCM 2.0 Programming User's Guide Page 234
- Page / 446
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
234 Configuring Enterprise Edge Services
Enterprise Edge 2.0 Programming Operations Guide P0911588 Issue 01
Add a Rule to an Interface
3. Under Configuration, click Add Rule.
The Rule Setting dialog box appears.
4. Configure the Rule settings according to the following table:
Note: If you do not configure the public and private masks correctly the
system will be affected. You must specify addresses that exist. For
example, if you configure an outbound rule, the Public IP address and
Public Mask are the translated addresses. These addresses must be
assigned or packets will be sent to a non-existent destination. For
inbound rules, the translated address is the Private Address and Mask.
5. Click Save.
6. When you finish adding rules, configure the Rule Order box in the Rule
Configuration screen for the interface.
Note: Configure the rule order from most specific to most general. For
example, a TCP rule for one port should come before a general rule for
all TCP traffic. IP rules should come last.
7. Press Tab to update the screen.
Attribute Description
Rule Name (R#) Allows you to assign a number to the Rule.
Direction Allows you to choose if the direction of the rule is In, Out or Both. Both only
applies to IP protocols.
Protocol Allows you to choose the protocol for this interface; IP, TCP, UDP,orTCP/
UDP.
Private IP Type Allows you to specify if the IP type is Fixed or Dynamic.
The default is Fixed.
Private IP Allows you to specify the Private IP address. The Rule is invalid without this
IP address.
Private Mask Allows you to specify the mask to use with the Private IP.
Private Port
Range (#-#)
Allows you to specify a single or range of entries (1-65535) or the following;
ALL, FTP, Telnet, SMTP, DNS, Finger, HTTP, H.323, POP3, NNTP,
RPC, SUNNFS, SNMP, SNMP-TRAP, TFTP and Gopher.
Public IP Type Allows you to specify if the IP type is Fixed or Dynamic.
The default is Fixed.
Public IP Allows you to specify the Public IP address. This address should be on the
outside network.
Public Mask Allows you to specify the mask to use with the Public IP.
If you enter 255.255.255.255 then the Public IP is a single address.
If you enter 0.0.0.0 then the Public IP is all possible addresses.
Public Port
Range (#-#)
Allows you to specify a single or range of entries (1-65535) or the following;
ALL, FTP, Telnet, SMTP, DNS, Finger,HTTP,H.323,POP3,NNTP,
RPC, SUNNFS, SNMP, SNMP-TRAP, TFTP and Gopher.
- Enterprise Edge 2.0 1
- Programming Operations 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Contents 9 9
- 10 Contents 10
- Contents 11 11
- Glossary 395 12
- Index 437 12
- About this document 13
- Related documents 14
- Regulations 15
- Enhanced 911 Configuration 16
- Radio-frequency interference 16
- Hearing-aid compatibility 17
- Electromagnetic compatibility 17
- Use of a music source 18
- Software licensing 21
- 22 About this document 22
- Enterprise Edge Overview 23
- 24 Enterprise Edge Overview 24
- Enterprise Edge Overview 25 25
- 26 Enterprise Edge Overview 26
- Enterprise Edge Overview 27 27
- Unified Manager 28
- Enterprise Edge Overview 29 29
- Enterprise Edge Overview 31 31
- Enterprise Edge Overview 33 33
- 34 Enterprise Edge Overview 34
- Logging on to Enterprise Edge 37
- Logging off Enterprise Edge 40
- Configuring system settings 41
- System registration 42
- To view LAN performance: 49
- Frame Relay 50
- Point-to-Point-Protocol (PPP) 50
- WAN Data Compression 50
- Parameters: 55
- Configuring a 59
- Net Link 59
- Deleting an ISDN interface 63
- Media Services Card 66
- Media Bay Modules 69
- Media Bay Modules (cont’d) 70
- Provision lines 81
- Programming order 83
- Programming Services 84
- Viewing all Services 85
- Statuses 86
- Telepho ny Ser vices 87
- Terminals & sets 90
- Line access 93
- OLI number 95
- Capabilities 98
- User preferences 102
- Restrictions 103
- Telco features 106
- Control set 109
- Trunk/line data 111
- Line type on page 116 112
- Assigning DNs 123
- Restriction filters 124
- Time & date 127
- Call Routing 128
- Routes and destination codes 129
- Destination codes 131
- Services: Routing Service) 134
- Scheduled Services 138
- Ringing service 139
- Restriction service 141
- Routing Service 142
- Common Settings 143
- System speed dial 145
- General Settings 147
- Feature settings 148
- Park mode on page 150 149
- Call log space 151
- Direct dial 153
- CAP assignment 154
- Private DN lengths 155
- Access codes 156
- Remote access packages 160
- COS Passwords 160
- DN lengths 162
- Network Name Display 163
- (virtual network) 167
- Network Services 169
- Hunt groups 170
- , Hunt groups 171
- Moving members of a group 172
- Setting the Distribution mode 174
- Setting the hunt delay 174
- Programming busy line setting 175
- Queue time-out 175
- Overflow set 175
- Companion 177
- Radio data 179
- Cell assignment 180
- Cell Radios 180
- Register individual portables 181
- Hospitality 183
- Alarm time (AL) feature 184
- Set/room settings 185
- Call permissions 185
- Alarm data 186
- Voice Mail 188
- Call Detail Recording 188
- Console Service 189
- VoIP Gateway 189
- IP Routing 200
- IPX Routing 208
- WAN Overview 222
- 4. Click Save 224
- filters in 226
- QoS monitor 227
- Web cache 228
- Net Link Manager 229
- Alarm Service 232
- IP Firewall Filters 235
- Signalling System1 241
- DPNSS 1 capabilities 242
- DPNSS 1 features 242
- Three Party Service 243
- Diversion 243
- Restrictions by set type 244
- Redirection 245
- Executive Intrusion 245
- Intrusion levels 246
- Call Offer 247
- Route Optimization 248
- Message Waiting Indication 249
- Loop avoidance 252
- User Manager 253
- Alarm Manager 256
- Maintenance 259
- Warm reset 260
- Backup and restore 260
- Maintenance 261 261
- 264 Maintenance 264
- Manager’s Tools menu 265
- 266 Maintenance 266
- 268 Maintenance 268
- Maintenance 269 269
- Maintenance 275 275
- ICMP Counters 275
- 276 Maintenance 276
- UDP Counters 276
- TCP Counters 276
- System version 278
- Media Bay Module status 279
- System test log 282
- System administration log 283
- Network event log 284
- Alarm codes 285
- Event messages 285
- Maintenance 295 295
- CSU statistics 297
- Maintenance 299 299
- 300 Maintenance 300
- Link Status 301
- Moving telephones 302
- 304 Maintenance 304
- Getting ready 306
- Types of problems 306
- Fault Alarm Banner 308
- Problems with telephones 309
- Problems with lines 310
- Problems with external paging 317
- Problems with module service 318
- Dialed number gets busy tone 322
- Dialedfeaturecodegetsbusytone 324
- Services 325
- Appendix A: Network Examples 327
- Access using Enterprise Edge 328
- Lines used for networking 328
- PRI lines 329
- BRI lines 330
- Remote access on PRI trunks 332
- Remote access on DPNSS lines 332
- Enterprise Edge security 333
- Coordinated dialing plans 335
- Routing service (continued) 336
- System A 340
- System B 340
- System D 340
- System C 340
- Networking examples 341
- PRI (SL-1) 343
- PRI (public protocol) 343
- (public protocol) 349
- PRI/BRI QSIG 357
- Public networking scenarios 362
- Enterprise Edge 363
- Central Office 363
- Private networking scenarios 365
- PRI DID and 2-way DID 370
- Appendix B: ISDN Overview 371
- Types of ISDN service 372
- ISDN layers 372
- ISDN Bearer capability 373
- PRI services and features 373
- BRI services and features 373
- 374 Appendix B: ISDN Overview 374
- Appendix B: ISDN Overview 375 375
- 376 Appendix B: ISDN Overview 376
- ISDN hardware 377
- BRI hardware 378
- Clock Source for ISDN 379
- ISDN standards compatibility 380
- Planning your ISDN network 380
- Ordering ISDN PRI 381
- Ordering ISDN BRI 381
- Supported ISDN protocols 382
- ISDN programming 383
- 384 Appendix B: ISDN Overview 384
- Appendix B: ISDN Overview 385 385
- Program ISDN equipment 386
- Appendix B: ISDN Overview 387 387
- 388 Appendix B: ISDN Overview 388
- System defaults 392
- Glossary 395
- 396 Glossary 396
- Glossary 397 397
- 398 Glossary 398
- Glossary 399 399
- 400 Glossary 400
- Glossary 401 401
- 402 Glossary 402
- Glossary 403 403
- 404 Glossary 404
- Glossary 405 405
- 406 Glossary 406
- Glossary 407 407
- 408 Glossary 408
- Glossary 409 409
- 410 Glossary 410
- Glossary 411 411
- 412 Glossary 412
- Glossary 413 413
- 414 Glossary 414
- Glossary 415 415
- 416 Glossary 416
- Glossary 417 417
- 418 Glossary 418
- Glossary 419 419
- 420 Glossary 420
- Glossary 421 421
- 422 Glossary 422
- Glossary 423 423
- 424 Glossary 424
- Glossary 425 425
- 426 Glossary 426
- Glossary 427 427
- 428 Glossary 428
- Glossary 429 429
- 430 Glossary 430
- Glossary 431 431
- 432 Glossary 432
- Glossary 433 433
- 434 Glossary 434
- Glossary 435 435
- 436 Glossary 436
- (‡) uses two of 436
- , 153, 157 439
- , 285, 289 445
Related products and manuals for Gateways/controllers Avaya BCM 2.0 Programming
Gateways/controllers Avaya Mobile Communication 3100 Planning and Engineering User Manual
(52 pages)
(52 pages)
Gateways/controllers Avaya 3.6/SRG Notice
(14 pages)
(14 pages)
Gateways/controllers Avaya Configuring BayRS Routers and Protocols (308665-14.20 Rev 00) User Manual
(26 pages)
(26 pages)
Gateways/controllers Avaya B5800 User Manual
(342 pages)
(342 pages)
Gateways/controllers Avaya B5800 Notice
(12 pages)
(12 pages)
Gateways/controllers Avaya Reference for BCC IP show Commands (308603-14.20 Rev 00) User Manual
(78 pages)
(78 pages)
Samsung SCB-1001P manuales
Manuales del propietario y guías del usuario para Cámaras De Seguridad Samsung SCB-1001P.
Ofrecemos 1 manuales en pdf Samsung SCB-1001P para descargar gratis por tipos de documentos: Manual de usuario
Samsung SCB-1001P Manual de usuario (32 paginas)
Marca: Samsung | Categoria: Security cameras | Tamaño: 2.27 MB |
Tabla de contenidos
Contents
8
Introduction
10
Connection
16
IIIIIIIII
19
IIIIIIII
19
EXPOSURE
20
BACKLIGHT
22
DAY/ NIGHT
23
IIIIIIIIII
25
IIIIIIIIIII
25
26_ Setup
26
English_29
29
Más productos y manuales para Cámaras De Seguridad Samsung
| Modelos | Tipo de documento |
|---|---|
| SMO-151QNP |
Guía de usuario
Samsung SMO-151QNP User manual,
112 paginas
|
| SND-560 |
Manual de usuario
1/3-Zoll-CCD High Performance WDR-Netzwerk,
43 paginas
|
| SCC-B9221 - IR Bullet Camera |
Instrucciones de operaciones
Samsung SCC-B9221 - IR Bullet Camera Operating instructions,
12 paginas
|
| SID-450 |
Manual de instrucciones
Samsung SID-450 Instruction manual,
22 paginas
|
| SCC-B531xP |
Guía de usuario
   
Samsung SCC-B531xP User`s guide,
118 paginas
|
| SND-6011R |
Guia de preparacion
Samsung SND-6011R Setup guide,
45 paginas
|
| SCC-B2033P |
Manual de usuario
Samsung SCC-B2033P User manual,
32 paginas
|
| SCC-B2031P |
Manual de usuario
Samsung SCC-B2031P User manual,
30 paginas
|
| SCC-643(P) |
Manual de usuario
SCC-641(P)/SCC,
2 paginas
|
| SHC-721PH |
Manual de instrucciones
Samsung SHC-721PH Instruction manual,
24 paginas
|
| SCD-1080P |
Manual de usuario
Samsung SCD-1080P User manual,
32 paginas
|
| SCO-2080RH |
Manual de usuario
Samsung SCO-2080RH User manual,
40 paginas
|
| C6435(P) |
Manual de usuario
SCC-C6435(P)/C6433(P),
80 paginas
|
| SID-370 |
Manual de usuario
Samsung SID-370 User`s manual,
25 paginas
|
| SNC-B2335P |
Manual de usuario
SNCB2335P IP-Kameras - Pro-4-Pro,
10 paginas
|
| SDZ-3750T |
Manual de usuario
Samsung SDZ-3750T User`s manual,
41 paginas
|
| SCC-B535x(S) |
Manual de usuario
SAMSUNG | GVI Security 2009 Camera Line Up,
61 paginas
|
| SCC-5399N |
Manual de usuario
Samsung SCC-5399N User manual,
34 paginas
|
| SNC-B2331(P) |
Manual de usuario
Телекамера SNC-B2331P - Samsung,
100 paginas
|
| SCC-C6407 |
Manual de instrucciones
Samsung SCC-C6407 Instruction manual,
31 paginas
|
© 2020, manymanuals.com. All rights reserved. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals