Avaya S8300 User Manual Page 119
- Page / 768
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
About installation and cabling
Issue 9.1 June 2006 119
Connecting the Safety Ground
Proper grounding of the G700 Media Gateway installation safeguards the system, users and
service personnel by providing protection from lightning, power surges, AC mains faults, power
crosses on central office trunks, and electrostatic discharge (ESD).
Local electrical installation codes must be followed when installing G700 Media Gateways.
!
WARNING:
WARNING: Connection of both grounds (through the AC or DC Power Cord and the
Supplementary Ground Conductor) is required for safe operation of the G700
Media Gateway.
!
WARNING:
WARNING: An improper ground can cause electrical shock as well as equipment failures and
service outages.
To attach the ground wires
1. Remove the ground screw on the rear of the chassis adjacent to the ground symbol:
2. Place the ring terminal of the 10 AWG (4.0 mm
2)
Supplementary Ground Conductor on the
screw.
3. Replace the ground screw to the chassis and securely tighten the screw such that it cannot
be loosened without the use of a tool.
The ground block is provided for use with more than one G700 (or other Cajun devices) in the
rack. It is usually mounted by the customer electrician.
If the ground block has been purchased: Proceed with step 4; otherwise, proceed with
step 7
.
4. Cut the Supplementary Ground Conductor (which has one end attached to the grounding
screw on the chassis) to the length needed to terminate it into one of the terminals of the
ground block.
Do not coil the Supplementary Ground Conductor.
5. Attach one end of the remaining 10 AWG (4mm
2
) ground wire to one of the terminals in the
ground block and the other end to an approved ground.
6. Cut this ground wire to the length needed to reach the approved ground.
Do not coil this wire.
- Installing and Upgrading 1
- Issue 9.1 June 2006 5 5
- Issue 9.1 June 2006 7 7
- Issue 9.1 June 2006 9 9
- Contents 10
- Issue 9.1 June 2006 11 11
- Issue 9.1 June 2006 13 13
- Issue 9.1 June 2006 15 15
- Issue 9.1 June 2006 17 17
- Issue 9.1 June 2006 19 19
- Issue 9.1 June 2006 21 21
- Issue 9.1 June 2006 23 23
- About this book 25
- Conventions 27
- Terminology 28
- Typography 28
- Commands 29
- Downloading this book 30
- Related resources 31
- Technical assistance 32
- Trademarks 33
- Ordering Documentation 33
- Sending us comments 34
- Section 1: Reference 35
- What wizards are available 37
- When to use each wizard 38
- Issue 9.1 June 2006 39 39
- Issue 9.1 June 2006 41 41
- The Installation Wizard 43
- Issue 9.1 June 2006 45 45
- Issue 9.1 June 2006 47 47
- The Software Update Manager 48
- Issue 9.1 June 2006 49 49
- The Upgrade Tool 50
- Issue 9.1 June 2006 51 51
- ● G350 Media Gateway 52
- Issue 9.1 June 2006 53 53
- The Network Region Wizard 55
- Issue 9.1 June 2006 57 57
- Issue 9.1 June 2006 59 59
- Issue 9.1 June 2006 61 61
- About connection methods 63
- Issue 9.1 June 2006 65 65
- Terminal Emulator, or ASA): 66
- Issue 9.1 June 2006 67 67
- Issue 9.1 June 2006 69 69
- About Log in Methods 70
- To run telnet 71
- To run the Web Interface 72
- Issue 9.1 June 2006 73 73
- Main Menu 74
- Issue 9.1 June 2006 75 75
- To run SAT: 76
- Issue 9.1 June 2006 77 77
- Issue 9.1 June 2006 79 79
- Issue 9.1 June 2006 81 81
- Communication Manager 82
- About hardware components 83
- What are the media modules 84
- Figure 3: Media modules 85
- X330W-4DS1 86
- Issue 9.1 June 2006 87 87
- C363T Multilayer switch 88
- Building a stack 89
- Stack Master election rules 91
- 1. Stack Master 92
- Issue 9.1 June 2006 93 93
- About installation planning 95
- What site verification does 97
- AUDIX Messaging Application 97
- Maintaining system security 98
- Issue 9.1 June 2006 99 99
- Power Verification 100
- Grounding Verification 100
- Issue 9.1 June 2006 101 101
- Issue 9.1 June 2006 103 103
- Issue 9.1 June 2006 105 105
- Inserting media modules 107
- To insert media modules 108
- Issue 9.1 June 2006 109 109
- Inserting an Expansion Module 110
- Issue 9.1 June 2006 111 111
- Cabling multiple units 112
- Attaching Ground Conductors 116
- What are approved grounds 117
- ● Acceptable water pipe 118
- ● Concrete encased ground 118
- ● Ground ring 118
- ● Approved floor grounds 118
- Connecting the Safety Ground 119
- Connecting AC Power 120
- Issue 9.1 June 2006 121 121
- Plugging in AC power 122
- To check DC power 123
- Section 2: G700 installation 125
- Checklist 1: 126
- Install a New G700 126
- Issue 9.1 June 2006 127 127
- Checklist 2: 129
- Installation Wizard 129
- Checklist 3 131
- Checklist 4 133
- Issue 9.1 June 2006 135 135
- Checklist 5: 136
- Issue 9.1 June 2006 137 137
- Installation Overview 138
- About access to the Server CD 139
- System Access 140
- Issue 9.1 June 2006 141 141
- Issue 9.1 June 2006 143 143
- Issue 9.1 June 2006 145 145
- Completing the RFA process 146
- Issue 9.1 June 2006 147 147
- To run the ART 148
- (Avaya technicians only) 148
- Install the S8300 149
- Setting telnet parameters 150
- To begin the upgrade 151
- Issue 9.1 June 2006 153 153
- Issue 9.1 June 2006 155 155
- Enabling Network Time Servers 157
- Issue 9.1 June 2006 159 159
- Custom template (S8300 only) 160
- Issue 9.1 June 2006 161 161
- Usage Options screen 162
- Issue 9.1 June 2006 163 163
- Issue 9.1 June 2006 165 165
- Issue 9.1 June 2006 167 167
- Issue 9.1 June 2006 169 169
- Issue 9.1 June 2006 171 171
- Issue 9.1 June 2006 173 173
- To reset the System 174
- To assign node names 174
- Administering Network Regions 175
- Administering IP Interfaces 177
- Issue 9.1 June 2006 179 179
- ● Administering IP Interfaces 180
- Issue 9.1 June 2006 183 183
- Issue 9.1 June 2006 185 185
- Issue 9.1 June 2006 187 187
- To add a media gateway 189
- To verify changes 191
- Survivable Processor 193
- (if the Primary Controller) 195
- Integrated Messaging 196
- (for an S8300 LSP) 197
- Issue 9.1 June 2006 199 199
- Installation overview 200
- Issue 9.1 June 2006 201 201
- Issue 9.1 June 2006 203 203
- Configure the G700 204
- Issue 9.1 June 2006 205 205
- Issue 9.1 June 2006 209 209
- Issue 9.1 June 2006 211 211
- 03-300412 212
- Issue 9.1 June 2006 215 215
- Issue 9.1 June 2006 217 217
- Issue 9.1 June 2006 219 219
- ● Test the endpoints 224
- ● Enable adjunct systems 224
- Issue 9.1 June 2006 225 225
- Release 3.1 upgrade scenarios 227
- Accessing the S8300 228
- Accessing the Server CD 228
- Issue 9.1 June 2006 229 229
- Issue 9.1 June 2006 231 231
- Obtaining service pack files 233
- Issue 9.1 June 2006 235 235
- To access the SAT 239
- To clear alarms 241
- To check link status 241
- To record all busyouts 242
- To save translations 242
- To disable alarm origination 243
- (if IA770 is being used) 244
- Issue 9.1 June 2006 245 245
- Backing up system files 247
- To back up data 248
- Issue 9.1 June 2006 249 249
- Upgrading the S8300A 251
- Issue 9.1 June 2006 253 253
- Linux migration backup 254
- Issue 9.1 June 2006 255 255
- Issue 9.1 June 2006 257 257
- Issue 9.1 June 2006 259 259
- Issue 9.1 June 2006 261 261
- Issue 9.1 June 2006 263 263
- Verifying software version 264
- Copying files to the S8300 265
- Issue 9.1 June 2006 267 267
- Verifying connectivity 268
- To verify connectivity 269
- Restoring data 270
- Restart the server 271
- Issue 9.1 June 2006 273 273
- ● Translations: xln files 274
- ● System: os files 274
- ● Security: security files 274
- Reboot the media server 275
- Issue 9.1 June 2006 277 277
- Issue 9.1 June 2006 279 279
- Verifying operation 280
- Next steps 281
- Issue 9.1 June 2006 283 283
- Post-upgrade tasks 284
- If using IA770: 285
- Issue 9.1 June 2006 287 287
- Saving translations 289
- Complete the upgrade process 290
- To busy out trunks 291
- To resolve alarms 291
- To back up the system 291
- Issue 9.1 June 2006 293 293
- Issue 9.1 June 2006 295 295
- Issue 9.1 June 2006 297 297
- Post-upgrade service pack 300
- Issue 9.1 June 2006 301 301
- Issue 9.1 June 2006 303 303
- Issue 9.1 June 2006 305 305
- To access SAT 307
- To determine other languages 312
- Issue 9.1 June 2006 313 313
- Shutting down IA770 314
- Issue 9.1 June 2006 315 315
- ● Server and System Files 316
- ● Security Files 316
- R2.x only) 317
- Issue 9.1 June 2006 319 319
- Issue 9.1 June 2006 321 321
- Preparing LSPs 322
- Issue 9.1 June 2006 323 323
- ● This server’s CD-ROM drive 324
- Issue 9.1 June 2006 325 325
- LSPs, and G700 media gateways 327
- Issue 9.1 June 2006 329 329
- Running the upgrade 330
- Issue 9.1 June 2006 331 331
- Issue 9.1 June 2006 337 337
- Issue 9.1 June 2006 339 339
- Issue 9.1 June 2006 341 341
- H.323 (optional) 342
- S8300 using the Upgrade Tool 343
- About system access 344
- Issue 9.1 June 2006 345 345
- Issue 9.1 June 2006 347 347
- Issue 9.1 June 2006 349 349
- Issue 9.1 June 2006 351 351
- Issue 9.1 June 2006 355 355
- Issue 9.1 June 2006 357 357
- Connecting telephones 359
- Figure notes: 360
- Issue 9.1 June 2006 361 361
- EMERGENCY 363
- TRANSFER 363
- Local and Phantom Power 366
- Using the 1152A1 PDU 367
- Issue 9.1 June 2006 369 369
- 1151B2/C2 power supplies 371
- Available PoE Switch Options 373
- Power priority mechanism 374
- Issue 9.1 June 2006 375 375
- Stacking 376
- Layer 2 features 376
- Layer 3 features 377
- Management 377
- Power over Ethernet (PoE) 378
- Issue 9.1 June 2006 379 379
- Using the P333T-PWR switch 381
- Connecting the cables 382
- To install the CBC: 383
- Issue 9.1 June 2006 385 385
- Issue 9.1 June 2006 387 387
- (for the S8300 Media Server) 388
- Call center 389
- Issue 9.1 June 2006 391 391
- Avaya Integrated Management 392
- Issue 9.1 June 2006 393 393
- Avaya Proxy Agent 394
- Avaya Configuration Manager 394
- Avaya Site Administration 395
- Avaya Terminal Configuration 395
- Avaya Terminal Emulator 395
- Avaya VoIP Monitoring Manager 396
- Issue 9.1 June 2006 397 397
- Terminal server installation 399
- Issue 9.1 June 2006 401 401
- Administering the IOLAN+ 402
- To connect the IOLAN+ 403
- Issue 9.1 June 2006 405 405
- To reboot the IOLAN+ 406
- Administering the gateway 407
- Administering an IOLAN+ port 407
- Issue 9.1 June 2006 409 409
- Administering IP services 411
- To administer IP services 412
- Call detail recording (CDR) 413
- Administering CDR parameters 414
- To administer CDR parameters 415
- CDR LINK STATUS 416
- Primary Secondary 416
- Maintenance Busy? no 416
- Downloading the RDTT package 417
- Printers 418
- DS1/T1 CPE loopback jack 419
- Administering a loopback jack 421
- To test the DS1 span 422
- Issue 9.1 June 2006 423 423
- To restore DS1 administration 425
- 123456 87 427
- E1/T1 EIA 530A DCE 427
- EISO EMSM EOSI 427
- MM710 multi-media module 429
- Issue 9.1 June 2006 433 433
- External modems 434
- Issue 9.1 June 2006 435 435
- Music-on-hold 437
- Adjunct Information Sources 442
- ASAI and DEFINITY LAN Gateway 443
- Avaya Interactive Response 443
- SIP Enablement Services 444
- Call Accounting Systems 444
- Section 3: G700 installation 445
- Install a new G700 446
- Issue 9.1 June 2006 447 447
- S8300A to R3.0 451
- S8300B to R3.0 453
- Issue 9.1 June 2006 457 457
- Issue 9.1 June 2006 461 461
- Issue 9.1 June 2006 463 463
- Issue 9.1 June 2006 471 471
- Issue 9.1 June 2006 473 473
- Verifying Software Version 475
- ● License file 476
- ● Avaya authentication file 476
- ● New firmware files 476
- Issue 9.1 June 2006 477 477
- Issue 9.1 June 2006 479 479
- Saving Translations 480
- Configuring the S8300 481
- Issue 9.1 June 2006 483 483
- Issue 9.1 June 2006 485 485
- Issue 9.1 June 2006 487 487
- Issue 9.1 June 2006 489 489
- Issue 9.1 June 2006 491 491
- Issue 9.1 June 2006 493 493
- ● The key number 494
- ● The encryption type 494
- ● The key code 494
- To create the key file 495
- To upload the keys file 495
- Issue 9.1 June 2006 497 497
- ● Checking for IP connections 498
- Issue 9.1 June 2006 499 499
- Issue 9.1 June 2006 501 501
- Checking for IP connections 502
- Issue 9.1 June 2006 503 503
- To set LSP transition points 505
- Issue 9.1 June 2006 507 507
- Issue 9.1 June 2006 509 509
- To install MGP firmware 510
- Issue 9.1 June 2006 511 511
- Issue 9.1 June 2006 513 513
- Issue 9.1 June 2006 515 515
- Issue 9.1 June 2006 519 519
- Issue 9.1 June 2006 521 521
- Issue 9.1 June 2006 523 523
- Issue 9.1 June 2006 525 525
- Issue 9.1 June 2006 529 529
- Issue 9.1 June 2006 531 531
- Issue 9.1 June 2006 533 533
- Issue 9.1 June 2006 535 535
- Issue 9.1 June 2006 537 537
- ● OSS Method 538
- ● SNMP Method 538
- Issue 9.1 June 2006 539 539
- Issue 9.1 June 2006 545 545
- Issue 9.1 June 2006 547 547
- Issue 9.1 June 2006 549 549
- Issue 9.1 June 2006 551 551
- Issue 9.1 June 2006 553 553
- To run the ping command 556
- Issue 9.1 June 2006 557 557
- Issue 9.1 June 2006 561 561
- Issue 9.1 June 2006 563 563
- Issue 9.1 June 2006 565 565
- Issue 9.1 June 2006 567 567
- Issue 9.1 June 2006 571 571
- Issue 9.1 June 2006 573 573
- Issue 9.1 June 2006 577 577
- Issue 9.1 June 2006 581 581
- Issue 9.1 June 2006 583 583
- Issue 9.1 June 2006 585 585
- Issue 9.1 June 2006 587 587
- Issue 9.1 June 2006 589 589
- Issue 9.1 June 2006 593 593
- ● Login ID and password 594
- ● IP address 594
- Issue 9.1 June 2006 595 595
- To download a service pack 596
- Issue 9.1 June 2006 597 597
- Issue 9.1 June 2006 609 609
- Issue 9.1 June 2006 613 613
- Issue 9.1 June 2006 617 617
- Issue 9.1 June 2006 619 619
- Issue 9.1 June 2006 621 621
- Issue 9.1 June 2006 623 623
- Issue 9.1 June 2006 625 625
- Issue 9.1 June 2006 627 627
- Issue 9.1 June 2006 631 631
- Issue 9.1 June 2006 637 637
- Issue 9.1 June 2006 641 641
- Issue 9.1 June 2006 643 643
- Issue 9.1 June 2006 647 647
- Issue 9.1 June 2006 651 651
- Issue 9.1 June 2006 653 653
- Issue 9.1 June 2006 657 657
- To verify operation 659
- To restart LSPs (if any) 664
- Issue 9.1 June 2006 665 665
- Issue 9.1 June 2006 667 667
- ● Authentication file 668
- Issue 9.1 June 2006 671 671
- Issue 9.1 June 2006 673 673
- Issue 9.1 June 2006 681 681
- Issue 9.1 June 2006 683 683
- Issue 9.1 June 2006 685 685
- (starting from R2.x only) 686
- Issue 9.1 June 2006 687 687
- Issue 9.1 June 2006 689 689
- Issue 9.1 June 2006 691 691
- Issue 9.1 June 2006 693 693
- Upgrade the S8300 694
- Issue 9.1 June 2006 695 695
- Issue 9.1 June 2006 697 697
- Issue 9.1 June 2006 699 699
- Making the upgrade permanent 700
- Upgrade the G700 Firmware 702
- Issue 9.1 June 2006 703 703
- Issue 9.1 June 2006 705 705
- Issue 9.1 June 2006 707 707
- Issue 9.1 June 2006 709 709
- Issue 9.1 June 2006 711 711
- Issue 9.1 June 2006 713 713
- Issue 9.1 June 2006 715 715
- To check media modules 717
- Issue 9.1 June 2006 719 719
- Issue 9.1 June 2006 721 721
- Issue 9.1 June 2006 723 723
- Issue 9.1 June 2006 725 725
- Issue 9.1 June 2006 727 727
- Issue 9.1 June 2006 729 729
- Issue 9.1 June 2006 731 731
- Issue 9.1 June 2006 733 733
- Cabling Equipment 734
- Issue 9.1 June 2006 735 735
- Technical information 736
- Issue 9.1 June 2006 737 737
- Installer's Checklist 738
- G700 Serial Numbers 739
- Information checklists 740
- Issue 9.1 June 2006 741 741
- Set Up for VoiP Resources 742
- Set Up for S8300 Media Server 743
- Installation Site Information 744
- Stack Layout 745
- Appendix C: Equipment list 747
- Equipment list 748
- Issue 9.1 June 2006 749 749
- Issue 9.1 June 2006 751 751
- Issue 9.1 June 2006 753 753
- Issue 9.1 June 2006 755 755
- Issue 9.1 June 2006 757 757
- Install the Avaya TFTP server 758
- Issue 9.1 June 2006 759 759
- Settings 760
- Issue 9.1 June 2006 761 761
- Numerical 763
Related products and manuals for Home Theater Systems Avaya S8300
Home Theater Systems Avaya S8300 User Manual
(22 pages)
(22 pages)
© 2020, manymanuals.com. All rights reserved. | 0.201 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals