Avaya T1 User Manual

Part No. 114942-B Rev 00October 2000600 Technology Park DriveBillerica, MA 01821-4130Installing T1 Link Modules in BN Platforms

xiFiguresFigure 1-1. Link Module Slots in a BLN Platform ...1-2Figure 1-2. Link Module Slots in a

xiiiTablesTable 1-1. Dual T1 Link Module Jumper Settings ...1-6Table 1-2. QMCT1 or QMCT1-DS0A Link

114942-B Rev 00 xv PrefaceRead this guide if you are responsible for installing a Nortel Networks® Dual T1, or Single-, Dual-, or Quad-Port Multichan

Installing T1 Link Modules in BN Platformsxvi 114942-B Rev 00 Text ConventionsThis guide uses the following text conventions:AcronymsThis guide uses

Preface114942-B Rev 00 xvii Hard-Copy Technical ManualsYou can print selected technical manuals and release notes free, directly from the Internet. G

114942-B Rev 001-1 Chapter 1Preparing for InstallationDepending on your configuration, complete these preliminary tasks as needed to install the T1 li

ii114942-B Rev 00 Copyright © 2000 Nortel NetworksAll rights reserved. October 2000.The information in this document is subject to change without noti

Installing T1 Link Modules in BN Platforms1-2114942-B Rev 00Figure 1-1. Link Module Slots in a BLN PlatformFigure 1-2. Link Module Slots in a BLN-2 Pl

Preparing for Installation114942-B Rev 001-3 Figure 1-3. Link Module Slots in a BCN PlatformPower OKPower OKPower OKPower OKLink module slots SRML QMC

Installing T1 Link Modules in BN Platforms1-4114942-B Rev 00Removing a Link ModuleIf there are no empty slots in your BN platform, you must remove a l

Preparing for Installation114942-B Rev 001-5 3.Loosen the captive screw on each end of the module.4.Grasp the sides of the module and pull it out of t

Installing T1 Link Modules in BN Platforms1-6114942-B Rev 00Setting Jumpers on the Dual T1 Link ModuleFigure 1-4 shows the user-configurable jumper on

Preparing for Installation114942-B Rev 001-7 Setting Jumpers on the QMCT1 and QMCT1-DS0A Link ModulesFigure 1-5 shows the user-configurable jumpers on

Installing T1 Link Modules in BN Platforms1-8114942-B Rev 00Figure 1-6 shows the user-configurable jumpers on the QMCT1-DS0A link module (Order No. AG

Preparing for Installation114942-B Rev 001-9 Table 1-2. QMCT1 or QMCT1-DS0A Link Module Jumper SettingsJumper Option Jumper Position DescriptionS1 Cab

114942-B Rev 002-1 Chapter 2Installing the Link ModuleComplete the steps in this chapter to install the T1 link module in your BLN, BLN-2, or BCN plat

114942-B Rev 00iiiEC Declaration of ConformityThis product conforms (or these products conform) to the provisions of Council Directive 89/336/EEC and

Installing T1 Link Modules in BN Platforms2-2114942-B Rev 002. Slide the module into the appropriate slot, using the slot card guides.Refer to Figure

Installing the Link Module114942-B Rev 002-3 Connecting CablesConnect the appropriate cabling to the link module ports.For 15-pin Sub-D (DB15) connect

114942-B Rev 003-1 Chapter 3Checking Status IndicatorsThis chapter describes the status indicator lights (or LEDs) on the Dual T1 link module, and on

Installing T1 Link Modules in BN Platforms3-2114942-B Rev 00Dual T1 LEDsFigure 3-1 shows the LEDs on the Dual T1 link module, and Table 3-1 describes

Checking Status Indicators114942-B Rev 003-3 Multichannel T1 (MCT1) Link Module LEDsThis section describes the LEDs on MCT1 link modules. Figure 3-2 s

Installing T1 Link Modules in BN Platforms3-4114942-B Rev 00Table 3-2. Functions of the MCT1 Link Module LEDs LED FunctionRED ALM (alarm) Indicates a

iv114942-B Rev 00Canada Requirements Only (continued)Repairs to certified equipment should be coordinated by a representative designated by the suppl

114942-B Rev 00vFCC Part 68 Compliance StatementThis equipment complies with Part 68 of FCC Rules. All direct connections to telephone network lines m

vi114942-B Rev 00Nortel Networks NA Inc. Software License AgreementNOTICE: Please carefully read this license agreement before copying or using the a

114942-B Rev 00viifor the security of its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost

ixContents PrefaceText Conventions ...........................xviAc