Avaya HRPSU User Manual

Part No. 114312 Rev. CNovember 1996 Installing and Maintaining the HRPSU

Installing and Maintaining the HRPSU1-4 114312 Rev. C For network devices that use 16-pin cables, you must install a connector adapter to attach the

Overview of the HRPSU 114312 Rev. C 1-5 • Review the installation procedures in Chapter 2. Read all safety sheets included with the shipment, and th

114312 Rev. C 2-1 Chapter 2Installing the HRPSU This chapter describes• Cabling options for network devices• Mounting the HRPSU in a surface stack o

Installing and Maintaining the HRPSU2-2 114312 Rev. C Using One 24-Pin Cable Figure 2-1 shows the cabling between a single 24-pin redundant power con

Installing the HRPSU 114312 Rev. C 2-3 Installing an Adapter for 16-Pin Cables If your network device uses 16-pin cables, you must install an adapte

Installing and Maintaining the HRPSU2-4 114312 Rev. C You can install up to four adapters on the HRPSU; however, only one network device may be attac

Installing the HRPSU 114312 Rev. C 2-5 Using One 16-Pin Cable Figure 2-3 shows the cabling between a single 16-pin redundant power connector on a ne

Installing and Maintaining the HRPSU2-6 114312 Rev. C Figure 2-4. Cabling with Two 16-Pin Cables Mounting the HRPSU You can mount the HRPSU on a flat

Installing the HRPSU 114312 Rev. C 2-7 Figure 2-5. HRPSU Mounted on a Surface To mount the HRPSU under a stack of devices, place the unit on a surfa

ii 114312 Rev. C4401 Great America Parkway 8 Federal StreetSanta Clara, CA 95054 Billerica, MA 01821 Copyright © 1988–1996 Bay Networks, Inc. All rig

Installing and Maintaining the HRPSU2-8 114312 Rev. C Mounting the HRPSU in a Rack This procedure requires• Three hardware packages from the HRPSU sh

Installing the HRPSU 114312 Rev. C 2-9 Figure 2-6. Locating the Rail Holes 3. Insert each angle bracket inside the rack in the area indicated in Fig

Installing and Maintaining the HRPSU2-10 114312 Rev. C Figure 2-7. Attaching Angle Brackets Run Boot Diag Local Power Height:5.25 in. (13

Installing the HRPSU 114312 Rev. C 2-11 4. Refer to Figure 2-8 and attach each flange to the HRPSU as follows. • When the HRPSU is to be mounted to s

Installing and Maintaining the HRPSU2-12 114312 Rev. C Figure 2-9. Mounting the HRPSU in an Enclosure Rack 6. Insert a 10-32 screw through each flange

Installing the HRPSU 114312 Rev. C 2-13 Installing a Power Supply Module in the HRPSU Power Rack The HRPSU power rack and the power supply modules a

Installing and Maintaining the HRPSU2-14 114312 Rev. CConnecting Cables and Switching on PowerWhen you have installed the power supply modules in the

Installing the HRPSU114312 Rev. C 2-15 8.Verify that the power is on by checking the LED on each HRPSU power supply module being used, and the redunda

114312 Rev. C 3-1 Chapter 3Maintaining the HRPSUThe HRPSU requires little maintenance. You should not open the HRPSU chassis. If you have any problems

114312 Rev. C iii USA Requirements Only Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment generates,

Installing and Maintaining the HRPSU3-2 114312 Rev. C5. Turn on the power supply module’s switch and verify that the green Power OK LED is lighted.Fig

114312 Rev. C A-1 Appendix ATechnical SpecificationsTable A-1. Physical SpecificationsHRPSU Power Rack Dimensions: (H) 5.25 in. by (W) 17.5 in. by (D)

Installing and Maintaining the HRPSUA-2 114312 Rev. CTable A-4. Electrical SpecificationsElectrical Line frequency: 47 to 63 HzVoltage amperes rating:

114312 Rev. C xiii About This GuideThis guide explains how to mount, install, and maintain a Bay Networks™ HRPSU (High Power Redundant Power Supply Un

114312 Rev. C ixFiguresFigure 1-1. HRPSU (High Power Redundant Power Supply Unit) ...1-1Figure 1-2. HRPSU Power Rack and Po

114312 Rev. C xiTablesTable 2-1. Options for Cabling a Network Device ...2-1Table 2-2 Status Indica

114312 Rev. C viiContentsAbout This GuideRelated Documentation ...

iv 114312 Rev. C Japan/Nippon Requirements Only Voluntary Control Council for Interference (VCCI) StatementVoluntary Control Council for Interferenc

viii 114312 Rev. CInstalling a Power Supply Module in the HRPSU Power Rack ...2-13Connecting Cables and Switching o

114312 Rev. C xv Technical Support and Online ServicesTo ensure comprehensive network support to our customers and partners worldwide, Bay Networks Cu

Installing and Maintaining the HRPSUxvi 114312 Rev. CBay Networks Customer Service If you purchased your Bay Networks product from a distributor or au

Technical Support and Online Services114312 Rev. C xvii Bay Networks Information ServicesBay Networks Information Services provide up-to-date support

Installing and Maintaining the HRPSUxviii 114312 Rev. CSupport Source CDThis CD-ROM -- sent quarterly to all contracted customers -- is a complete Bay

Technical Support and Online Services114312 Rev. C xix InfoFACTSInfoFACTS is the Bay Networks free 24-hour fax-on-demand service. This automated syste

114312 Rev. C v Bay Networks Software License This Software License shall govern the licensing of all software provided to licensee by Bay Networks

vi 114312 Rev. C Bay Networks Software License (continued) 9. Licensee shall not reverse assemble, reverse compile, or in any way reverse engineer

114312 Rev. C 1-1 Chapter 1Overview of the HRPSU This chapter describes the HRPSU (High Power Redundant Power Supply Unit) power rack and power supp

Installing and Maintaining the HRPSU1-2 114312 Rev. C The HRPSU supports devices requiring up to 210 watts of power, as well as those with lower powe

Overview of the HRPSU 114312 Rev. C 1-3 Hot-swap connectors on each power supply module connect the input and output signals of the power supply to