Avaya 8400B User's Guide Page 65
- Page / 198
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8400B Plus Data Module User’s Guide
555-020-709
Issue 2
November 1996
Configuration and Operation
3-19
Voice Operations
Dialing Instructions
When a voice call is made using the PC, the telephone number should be given
to the 8400B Plus Data Module in a single AT dial command as indicated in the
example below.
ATD P 9,1 (908) 555-1212
The P dial modifier must be included to tell the 8400B Plus Data Module that the
call is a voice call. If an attempt to dial a voice call is made using more than one
dial command on a command line, the first dial command will be accepted and
the second dial command may be discarded. After dialing the call, the 8400B
Plus Data Module automatically returns to the command mode.
A second voice call can be made from your PC by manually placing the first call
on HOLD, and then entering a dial command for the second call. Any attempt to
dial a second voice call while the first call is being dialed will be ignored.
Dialing Delay
To ensure that dialing does not begin before dial tone is received, dialing a voice
call will be delayed by the time stored in S-register S6 (Wait Time Before Blind
Dialing) and can be set to a maximum value of 255 seconds. The factory setting
of two seconds for S-register S6 is adequate for most calls.
Dialing Pause
A pause for second dial tone is normally required for calls outside the PBX. This
can be provided by including a comma between the outside line prefix (for
example, 9) and the first digit of the telephone number to be dialed. The comma
instructs the 8400B Plus Data Module, after dialing the prefix number, to pause
a fixed time before dialing the first digit of the telephone number. The pause
time is stored in S-register S8 (Duration of Delay For Comma Dial Modifier) and
can be set for any value up to a maximum of 255 seconds. The factory setting of
two seconds is adequate for most applications and should not be changed. If
added delay is required, additional commas can be added to the number.
ENTER
020709_2.book Page 19 Friday, April 23, 1999 5:39 AM
- 8400B Plus Data Module 1
- User’s Guide 1
- Contents 3
- About This Document 5
- Organization of This Guide 6
- How to Order Documentation 7
- How to Comment on This 7
- Document 7
- Conventions Used 8
- NETCON Data Channels 10
- PBX Security Measures 11
- Security Issues 12
- Lucent Technologies Fraud 13
- Intervention 13
- Related Documentation 13
- Important Safety Instructions 15
- SAVE THESE INSTRUCTIONS 16
- Introduction 17
- Features 18
- Physical Description 19
- Front Panel 20
- Rear Panel 21
- Power Supply Unit 23
- CAUTION: 23
- Installation 25
- Procedure 26
- LINEPHONE 27
- -7 +8 27
- What You Need 28
- Hardware Installation 32
- PBX Wall Jack 33
- Initial System Checks 35
- Installation Options 36
- US Companding 37
- Telephone Provides Dialing 37
- Disable Data Metering Feature 38
- Loopback Test 40
- LED Indications 42
- Status of Unit 43
- LED Description 43
- Selecting PC Communications 45
- Packages 45
- If You Are Using a PC 46
- Configuration and Operation 47
- Issuing Commands 48
- Command Buffer 49
- Command Line Set Up 49
- Command Acknowledgment 50
- Repeating a Command 51
- Sample Command Lines 52
- Configuration Parameters 53
- Data Operation 56
- Storing a Telephone Number 57
- Automatic Answering 59
- Remote Site Use 59
- A Sample On-Line Session 62
- Starting the Session 62
- Possible Display Problems 63
- Disconnecting a Data Call 63
- Voice Operations 64
- Dialing Instructions 65
- Dialing Delay 65
- Dialing Pause 65
- Sample Command Line 66
- Troubleshooting 69
- How to Use This Chapter 71
- S7 does 72
- ATDP9,555-1212 75
- ATDP9,,555-1212 75
- 1 in the example) to the 76
- AT&D0 76
- AT Command Set 79
- Continued: 85
- 555-020-709 100
- November 1996 100
- Dial Modifiers 111
- S-Registers 119
- Label Description 144
- Data Loopback Test 153
- Local Loopback Test 155
- Self-Test 158
- Remote Loopback Test 159
- Remote Loopback Test with 161
- Communications 163
- Arrangement 166
- Quick-Reference Summaries 169
- Pin Circuit 178
- Name Direction Lead Name 178
- Glossary 185
- D (dial) command 187
- D command 187
- AT command set 187
- 555-020-709 Issue 2 191
Related products and manuals for Telephones Avaya 8400B
Telephones Avaya CallPilot Fax User Manual
(52 pages)
(52 pages)
Telephones Avaya 4065R Quick Start Guide
(1 pages)
(1 pages)
Telephones Avaya T7406 User Manual
(2 pages)
(2 pages)
Telephones Avaya T7406 Installation Guide
(56 pages)
(56 pages)
Telephones Avaya 1120E Quick Start Guide
(3 pages)
(3 pages)
Telephones Avaya CallPilot Fax User's Guide
(30 pages)
(30 pages)
Telephones Avaya T7406E Configuration Guide
(58 pages)
(58 pages)
Telephones Avaya M7324 User Manual
(6 pages)
(6 pages)
Telephones Avaya BCM50 Configuration Guide
(328 pages)
(328 pages)
Telephones Avaya Contact Center User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 3.488 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals