Avaya Digital Mobility System Configuration Guide Page 165
- Page / 189
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 10 System Management 165
Digital Mobility System Installation and Configuration Guide
Viewing DMC restarts
1 Press MENU () - go to EXT. SERVICE.
2 Press 3/OK - go to STATISTICS.
3 Press 3/OK - go to DMC RESTART.
4 Press 3/OK.
5 The display will show date and time of the last DMC restart. Use the < > keys to access
information on dates and times of the previous DMC restarts.
Advanced features
This section provides information about the advanced features in the:
• “DMC OAM program” on page 165
• “Digital Mobility Service Tool” on page 177
DMC OAM program
The Advanced menu in the DMC OAM program contains several commands used for debugging
the system. It also contains a command for downloading software to the system.
Note: Use advanced settings only under the direction of your authorized service representative.
This section contains a description of each of these commands:
• “Status Message Level” on page 165
• “Enter Command Mode” on page 166
• “NVM (non-volatile memory)” on page 167
• “Dump” on page 168
• “RFP Slot Allocation” on page 169
• “Load Flash (updating software)” on page 173
Status Message Level
For more information, refer to “Checking Status Information” on page 143.
DM_InstallationGuide.book Page 165 Monday, September 18, 2006 6:58 AM
- N0000623 01.3 1
- September 18, 2006 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- Chapter 2 10
- Chapter 3 10
- Chapter 7 12
- Chapter 10 13
- 18 Figures 18
- 20 Tables 20
- Before you begin 21
- DECT and DECT variants 22
- Preface 23 23
- DMC GAP compliance 24
- Handset GAP compatibility 24
- How to get help 25
- Chapter overview 26
- Acronyms 27
- 28 Preface 28
- Chapter 1 29
- Overview 29
- Chapter 1 Overview 31 31
- 32 Chapter 1 Overview 32
- Chapter 1 Overview 33 33
- System Status LEDs 35
- System link (Secondary DMC) 35
- Serial port 36
- Base station connection 36
- TCM loop connection 36
- Power connection 36
- Installation overview 37
- Installation process map 38
- Digital Mobility Controller 39
- Environmental checklist 40
- Electrical requirements 40
- Base stations and repeaters 41
- Handsets 43
- Installation prerequisites 44
- Starting the DMC OAM program 45
- Exiting the DMC OAM program 53
- DMC OAM program main window 55
- Understanding the menu 55
- Understanding tabbed pages 56
- Master handset menu structure 59
- 3-key on model 59
- DMC installation 61
- System equipment for the DMC 62
- Chapter 3 DMC installation 63 63
- Install a DMC on another DMC 64
- Install a DMC on the wall 65
- 66 Chapter 3 DMC installation 66
- Chapter 3 DMC installation 67 67
- 68 Chapter 3 DMC installation 68
- TCM Loop connections 69
- TCM input connector pinout 69
- Next steps 70
- Chapter 5 71
- Repeater installation 71
- Installing the repeater 72
- Installing external antennas 74
- Chapter 4 83
- Base station installation 83
- Positioning a base station 84
- Installing the base stations 84
- Installing a base station 85
- Wiring the base station 87
- Chapter 6 91
- Preparing handset for use 91
- Battery information 92
- Charging battery 95
- Battery disposal 95
- Reading serial number 96
- Configuring the DMC 99
- Powering up the DMC 100
- Serial-IP converter 101
- N0000623 01.3 102
- Change password 105
- Suppression control 106
- Subscription setting 107
- Cable Delay Measurement 108
- Restart the DMC 110
- Next step 111
- Chapter 8 113
- Figure 74 Registration tab 114
- Setting up a Master handset 115
- Registering handsets 116
- 3/OK on the 120
- Subscribe handsets 121
- Handset features 124
- Idle display activation code 124
- Highest to lowest priority 125
- Do Not Disturb 125
- Handset system functions 127
- DMC Feature List 127
- Chapter 9 129
- Handset management 129
- Through Master handset 130
- Unsubscribing handsets 131
- Removing a directory number 132
- Removing a position 133
- Changing user settings 134
- Through the Master handset 135
- Changing authentication code 136
- Changing special rights 136
- Downloading firmware 137
- System Management 139
- 3/OK on the handset) 141
- Checking Status Information 143
- How to save status messages 144
- Repeater programming 145
- Handset adjustment 145
- System Information 149
- Change Password 150
- Date and Time 150
- Suppression Control 150
- Statistic 152
- Base station information 152
- Handset information 154
- General system information 155
- Measure Cable Delay 155
- Voice Path Gain 156
- PSTN Gain 157
- 5 Make an outgoing call 158
- DSP Tone Level 159
- Connection Settings 161
- Viewing handover statistics 164
- Viewing call statistics 164
- Advanced features 165
- Enter Command Mode 166
- NVM (non-volatile memory) 167
- RFP Slot Allocation 169
- Figure 117 DMC OAM: Slot 172
- Updating DMC software 173
- Digital Mobility Service Tool 177
- Download Flash 178
- Saving configuration data 181
- A Save as dialog box appears 182
- DMC OAM program 183
Related products and manuals for Telephones Avaya Digital Mobility System
Telephones Avaya CP Fax User Manual
(52 pages)
(52 pages)
Telephones Avaya BCM M7100N User Manual
(7 pages)
(7 pages)
Telephones Avaya I2004 Quick Start Guide
(2 pages)
(2 pages)
Telephones Avaya BCM 3.6 User Manual
(10 pages)
(10 pages)
Telephones Avaya CallPilot User's Guide
(114 pages)
(114 pages)
Telephones Avaya DECT Installation Manual
(129 pages)
(129 pages)
(10 pages)© 2020, manymanuals.com. All rights reserved. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals