Avaya BayStack AN and ANH Routers User Manual Page 127
- Page / 184
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuring the AN or ANH for Netboot and Directed Netboot
114113-B Rev. 00
A-3
Table A-1 describes the
ifconfig
command arguments for configuring a
synchronous interface.
Table A-1. ifconfig Command Arguments for a Synchronous Interface
Argument Description
Default Setting
-d Resets the AN/ANH IP interface settings to the default values. This argument tries
four WAN protocols in the following order until it successfully establishes a connection
to the network:
1. Bay Networks HDLC encapsulation (Bay Networks Standard Point-to-Point) with
external clocking
2. Frame Relay Annex D
3. Frame Relay LMI
4. Frame Relay Annex A
Frame Relay Settings
-fr
Configures the AN/ANH synchronous port as a frame relay connection. With this
argument, use one of the following options to specify a DLCMI setting:
-annexd
,
-annexa
, or
-lmi
.
-annexd
-annexa
-lmi
When one of these options is used with the
-fr
argument, it specifies a DLCMI setting.
Use the same setting as the network to which the router’s frame relay interface is
connected. The default setting for frame relay is
-annexd
.
Internal Clocking Setting
-int_clk
Sets the AN/ANH synchronous port to internal clocking at 1.25 MB/s. If you do not
specify the
-int_clk
option, the AN/ANH defaults to external clocking.
IP Connector Setting
<
interface
> Specifies the IP connector you are configuring. Use
com1, com2,
or
com3
(for
synchronous media).
IP Address Settings
<
IP address
> Specifies the IP address of the interface you set with
the
<interface>
variable. Provide
this address in dotted-decimal notation.
<
subnet mask
> Specifies the IP subnet mask of the interface you selected with the
<interface>
setting. Provide this address in dotted-decimal notation.
<
next hop address
> Specifies the IP address of the next-hop router. Provide this address in dotted-decimal
notation. Specify this address only if there are intermediate routers between the AN or
ANH and the BootP server.
- Installing and Operating 1
- BayStack AN and ANH 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 3
- European Requirements Only 3
- Canada Requirements Only 4
- Contents 9
- 114113-B Rev. 00 10
- About This Guide 21
- Before You Begin 22
- Conventions 22
- Acronyms 23
- Bay Networks Customer Service 25
- How to Get Help 26
- Chapter 1 27
- Installing the BayStack AN 27
- Preparing to Install the AN 29
- Supplying Tools and Equipment 31
- Removing the AN Enclosure 32
- Attaching the Protector 33
- Warning: 34
- Installing the AN 36
- Mounting the AN on a Wall 38
- Connecting an ISDN Cable 44
- Connecting Synchronous Cables 44
- Using the Crossover Switch 47
- Tighten the thumbscrews 48
- Connecting a Terminal Console 51
- Connecting a PC Console 53
- Connecting a Modem 54
- Caution: 55
- Connecting the Power Cable 57
- Chapter 2 59
- Verifying Shipment Contents 60
- Figure 2-1 61
- Supplying Equipment 63
- Verifying Site Requirements 64
- Installing the 8-Port ANH 65
- Access Node Hub 68
- Access Node Hub 69
- Connecting an AUI Cable 70
- MDI-X/MDI 72
- Figure 2-12. Linking Hubs 74
- Console cable plus 81
- COM 2COM 3/Expansion 85
- Chapter 3 87
- Software Installation 88
- Using EZ-Install 94
- *****Testing Memory***** 95
- AN_DIAG>> 98
- Figure 3-9. AN/ANH Netboot 100
- Continuing with Local Boot 104
- Starting the AN and ANH 107
- Chapter 4 109
- Operating the AN and ANH 109
- Access Node 110
- Front-Panel LEDs 112
- Back-Panel LEDs 112
- (continued) 113
- 8-Port ANH LED Descriptions 114
- (continued) 114
- ISDN-BRI 116
- Figure 4-4. AN Power Switch 118
- Resetting the AN or ANH 119
- Access Node 120
- Appendix A 125
- Configuring the AN or ANH 125
- Using the ifconfig Command 126
- Table A-1 describes the 127
- Table A-2 describes the 128
- <port #> 129
- Using the bconfig Command 130
- TFTP pathname 131
- Appendix B 133
- Wide Area Protocol Worksheets 141
- Configuring PPP 143
- Services 143
- SMDS Worksheet 145
- Appendix C 147
- Technical Specifications 147
- Electrical Specifications 148
- Environmental Specifications 148
- U.S. Safety Agency Approvals 149
- Configuring Dial Services 150
- Configuring 151
- BayStack Remote Access 151
- Hardware Summary 153
- Configuring Dial 154
- 10BASE-T Repeater Ports 156
- Synchronous Interface Options 157
- CAB0109A 158
- ISDN BRI Interface 159
- 56/64K DSU/CSU Interface 160
- FT1/T1 DSU/CSU Connections 160
- Local Console Connections 161
- Pin 6Pin 9 162
- Pin 1Pin 5 162
- Appendix D 163
- ANH Safety Status 164
- AE1101007, and AE1101008) 166
- V.28 Compliance 168
- V.35 Compliance 169
- ISDN BRI Requirements 174
- ISDN BRI Connector Pinouts 177
Related products and manuals for Routers Avaya BayStack AN and ANH Routers
Routers Avaya FE1/E1 User Manual
(26 pages)
(26 pages)
Routers Avaya BCM50 User Manual
(22 pages)
(22 pages)
Routers Avaya v1.02 Notice
(9 pages)
(9 pages)
Routers Avaya FE1/E1 User Manual
(24 pages)
(24 pages)
Routers Avaya BSGX4e User's Guide
(456 pages)
(456 pages)
Routers Avaya Passport ARN Routers User Manual
(166 pages)
(166 pages)
Routers Avaya BCC Quick Start Guide
(4 pages)
(4 pages)
Routers Avaya FireWall-1 User Manual
(56 pages)
(56 pages)
Routers Avaya BSG8/12 1.0 User Manual
(862 pages)
(862 pages)
Routers Avaya C360 User Manual
(238 pages)
(238 pages)
Routers Avaya P460 User Manual
(96 pages)
(96 pages)
Routers Avaya P114F User Manual
(14 pages)
(14 pages)
Routers Avaya M15-155 User Manual
(14 pages)
(14 pages)
Routers Avaya P460 User Manual
(224 pages)
(224 pages)
© 2020, manymanuals.com. All rights reserved. | 0.388 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals