Avaya BCM50 Installation Manual Page 45
- Page / 335
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2 Introducing the BCM50 hardware 45
Installation and Maintenance Guide
Trunk media bay modules
Trunk media bay modules connect telecommunications lines to the BCM50 system.
The table Trunk MBMs on page 45 lists the types of trunk media bay modules that are available
for the BCM50 system.
Digital trunk media bay module
The digital trunk media bay module (DTM) connects to a standard digital PSTN T1 or E1 carrier:
• On North American BCM50 systems, the DTM connects a T1 (24 channel) or PRI (23
channel) circuit to the BCM50. This PRI interface supports the NI-2 and MCDN protocol
variants.
• On International BCM50 systems, the DTM connects a 30 channel PRI, DASS2, or DPNSS
circuit to the BCM50. This PRI interface supports the ETSI Euro, ETSI QSIG, and MCDN
protocol variants.
The front bezel of the DTM has an RJ-48C connector that connects the DTM to the service
provider connection point. The faceplate also has a set of monitor jacks you can use to monitor the
span.
Six additional LEDs are on the front of the DTM. For information about these additional LEDs,
see DTM LEDs on page 67.
The figure DTM faceplate on page 46 shows the DTM module interfaces.
Table 3 Trunk MBMs
Module type Function Special notes
DTM
(see Digital trunk media bay
module on page 45)
Connects digital public switched
telephone lines to the BCM50 3.0
system.
Can connect to T1 or PRI-E1/T1
interfaces.
BRIM
(see Basic rate interface media
bay module on page 46)
Connects a maximum of four ISDN BRI
S/T interfaces.
—
GATM4/GATM8
(see Global Analog Trunk Module
on page 46)
Connects either four (GATM4) or eight
(GATM8) analog public switched
telephone lines to the BCM50 3.0
system.
—
ADID4/ADID8
(see Analog direct inward dialing
media bay module on page 47)
Connects either four (ADID4) or eight
(ADID8) analog DID interfaces.
—
R2MFC Provides MFC-R2 connectivity over an
E1 trunk.
For details about the R2MFC MBM,
see the R2MFC Media Bay Module
Installation and Configuration Guide
(NN40010-300).
Note: See Market profile attributes on page 285 for supported regions.
- BCM50 3.0 1
- Trademarks 2
- SOFTWARE LICENSE 3
- Task List 7
- 10 Task List 10
- NN40020-302 10
- Contents 11
- 18 Contents 18
- New in this release 19
- 20 New in this release 20
- Regulatory information 21
- EMI/EMC (FCC Part 15) 22
- Important safety instructions 23
- Use of a music source 24
- Enhanced 911 configuration 25
- Radio-frequency interference 25
- Additional safety information 27
- Chapter 1 29
- Symbols and text conventions 31
- Related publications 33
- How to get help 34
- Chapter 2 37
- ports and connectors 39
- Media bay modules 44
- Trunk media bay modules 45
- Global Analog Trunk Module 46
- Station media bay modules 47
- 4x16 media bay module 48
- BCM50 hardware 52
- Patch panel 53
- Wall-mount bracket 53
- BCM50 components 54
- Power supply 55
- Uninterruptable power supply 55
- Hard disk 56
- Cooling fan 57
- RJ-21 telephony connector 58
- Field-replaceable units 59
- Accessories 60
- Chapter 3 61
- LAN port LEDs 63
- Figure 30 MBM LEDs 66
- DTM LEDs 67
- BRIM LEDs 68
- Chapter 4 69
- (with integrated router) 70
- Chapter 5 73
- Chapter 6 77
- Digital loop 78
- Analog loop 78
- Basic hardware 79
- Optional equipment 79
- Other hardware and tools 79
- Chapter 7 81
- Unpacking the main unit 82
- To install the patch panel 85
- To install the WFC 90
- Attach feet here 91
- Chapter 8 95
- Unpacking the expansion unit 96
- To set GASM dip switches 98
- To set GATM dip switches 99
- To install an MBM 100
- Next step 101
- Chapter 9 103
- Connecting the expansion unit 104
- To connect an expansion unit 105
- Connecting the power supply 106
- Figure 51 Connect a UPS 107
- Wiring warnings 109
- G4x16/G8x16 112
- G8x16 MBMs 113
- Music source specifications 115
- Figure 52 Music source jack 116
- Chapter 10 119
- Installing IP phones 120
- Chapter 11 121
- Installing the ATA2 122
- To connect the ATA2 123
- Mounting the ATA2 123
- To mount the ATA2 on a wall 123
- Figure 57 ATA2 back view 124
- Mounting keyhole slots 124
- Configuring the ATA2 125
- Chapter 12 127
- Initial parameters overview 128
- Startup parameters overview 129
- Chapter 13 131
- To enter the keycodes 132
- To configure the IP address 133
- To configure the modem 133
- To select the region 134
- To initialize voice mail 134
- Chapter 14 137
- Prerequisites 138
- Accessing the BCM50 system 138
- To enter a keycode 139
- To configure IP Phones 144
- To configure SNMP settings 145
- To create user accounts 146
- Chapter 15 149
- Startup Profile requirements 150
- Configuring basic parameters 151
- Chapter 16 155
- To configure the MBM(s) 156
- Configuring modem settings 157
- Checking for software updates 157
- Configuring voice mail 157
- Customizing security policies 157
- Performing a backup 158
- Chapter 17 159
- Chapter 18 165
- To troubleshoot the main unit 166
- To test the expansion unit 166
- To test the MBM 167
- To test a station MBM 167
- To test a trunk MBM 167
- Reset to factory settings 169
- Activate the reset feature 170
- Table 32 Level 1 reset 172
- Table 33 Level 2 reset 172
- Chapter 19 173
- To shut down the system 174
- Chapter 20 175
- Removing the power supply 176
- Connect the new power supply 176
- Chapter 21 179
- Removing the main unit 180
- Installing the new main unit 181
- To connect the cables 182
- Chapter 22 183
- To remove the MBM 184
- To insert the new MBM 185
- Chapter 23 187
- Disconnecting the cables 188
- Removing the expansion unit 188
- Removing the MBM 190
- Chapter 24 193
- Special tools 194
- Opening the main unit case 194
- To open the main unit case 195
- To remove the hard disk 197
- To remove the fan 198
- Inserting the new component 199
- To insert the new hard disk 200
- Fan cable cutouts 201
- Fan cable clips 201
- To insert the new fan 202
- To insert the new router card 203
- Closing the main unit case 204
- Installing the main unit 205
- Connecting the cables 205
- Appendix A 207
- Appendix B 211
- Table 36 BRI line numbering 212
- Appendix C 213
- Table 37 LAN port wiring 214
- Appendix D 215
- Appendix E 217
- Appendix F 219
- Appendix G 221
- Appendix H 223
- Appendix I 225
- Digital interfaces 226
- Tones and cadences 227
- • Reorder, 1 kHz on page 233 228
- Functionality Attribute 237
- Market profile 237
- Russia South Africa 245
- Analog Trunk parameters 250
- GASM8 parameters 256
- GASI parameters 259
- ATA2 parameters 262
- ATA2 DR7 264
- Voicemail 265
- ISDN line services 268
- Trunk Types Description 269
- Appendix J 271
- Appendix K 275
- (Sheet 2 of 2) 276
- (Sheet 1 of 2) 277
- (Sheet 2 of 2) 278
- Appendix L 279
- Appendix M 283
- Appendix N 285
- • Reorder, 1 kHz on page 293 288
- Numerics 331
Related products and manuals for Routers Avaya BCM50
Routers Avaya BCM50e User Manual
(311 pages)
(311 pages)
Routers Avaya Cable User Manual
(194 pages)
(194 pages)
Routers Avaya FireWall-1 User Manual
(60 pages)
(60 pages)
Routers Avaya BCM50 User Manual
(50 pages)
(50 pages)
Routers Avaya BayRS Version 14.10 Notice
(42 pages)
(42 pages)
Routers Avaya BayRS, BCC, and Site Manager Software Version 14.20 Fixed Anomalies User Manual
(26 pages)
(26 pages)
Routers Avaya FireWall-1 User Manual
(54 pages)
(54 pages)
Routers Avaya Business Communications Manager - Administration - Remote Worker User Manual
(24 pages)
(24 pages)
Routers Avaya BCM50 Installation Manual
(295 pages)
(295 pages)
Routers Avaya 1600 Series User Manual
(100 pages)
(100 pages)
Routers Avaya BCM50e User Manual
(441 pages)
(441 pages)
© 2020, manymanuals.com. All rights reserved. | 0.294 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals