Avaya BCM50 Installation Manual Page 125
- Page / 295
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 11 Installing the analog terminal adapter 125
BCM50 Installation and Maintenance Guide
Figure 56 ATA2 pin outs
To connect the ATA2
1 Connect one end of a line cord to the ATA2 terminal jack.
2 Connect the other end to your telephone, modem, or fax.
3 Connect one end of a line cord to the ATA2 line jack.
4 Connect the other end to an available station port on the BCM50 system.
5 For a 120 V or 230 V system, plug the DIN connector of the power supply cord into the power
supply connector receptacle. Plug the adapter into a standard AC outlet.
Mounting the ATA2
After the ATA2 is correctly connected, you can mount the unit on a wall as described in this
section.
To mount the ATA2 on a wall
1 When using 0.5 mm wire (24-AWG), select a location within 800 m (2600 ft.) of the BCM50.
2 Allow 12.5 cm (5 in.) clearance for the line jack, terminal jack, and power supply connector.
3 Screw two 4-mm (#8) screws into the wall 130 mm (5.25 in.) apart. Leave 6 mm (0.25 in.) of
the two screws showing.
4 Align the slots at the back of the ATA2 unit over the screws. Push the unit against the wall.
The line jack, terminal jack, and power supply connector must be at the top of the ATA2. See
the figure ATA2 back view on page 126.
Caution: In North America, the ATA2 must be powered from a Class 2 power source that
is UL- and CSA-approved.
In Europe, the ATA2 must be powered from a Class II power source that is CE marked.
TCM*
TCM*
Ring (B-Lead)
Tip (A-Lead)
Line jack
Terminal jack
* The TCM input is not polarity sensitive.
- Document Status: Standard 1
- Document Number: NN40170-305 1
- Document Version: 03.03 1
- Date: August 2009 1
- Trademarks 2
- SOFTWARE LICENSE 3
- Task List 7
- 10 Task List 10
- NN40170-305 10
- Contents 11
- 18 Contents 18
- New in this release 19
- 20 New in this release 20
- Regulatory information 21
- EMI/EMC (FCC Part 15) 22
- Important safety instructions 23
- Use of a music source 24
- Enhanced 911 configuration 25
- Radio-frequency interference 25
- Additional safety information 27
- Chapter 1 29
- Symbols and text conventions 31
- Related publications 33
- How to get help 34
- Chapter 2 37
- ports and connectors 39
- Media bay modules 44
- Trunk media bay modules 45
- Global Analog Trunk Module 46
- Station media bay modules 47
- 4x16 media bay module 48
- BCM50 hardware 52
- Patch panel 53
- Wall-mount bracket 53
- BCM50 components 54
- Power supply 55
- Uninterruptable power supply 55
- Hard disk 56
- Cooling fan 57
- RJ-21 telephony connector 58
- Field-replaceable units 59
- Accessories 60
- Chapter 3 61
- LAN port LEDs 63
- Figure 30 MBM LEDs 67
- DTM LEDs 68
- BRIM LEDs 69
- Chapter 4 71
- (with integrated router) 72
- Chapter 5 75
- Chapter 6 79
- Digital loop 80
- Analog loop 80
- Basic hardware 81
- Optional equipment 81
- Other hardware and tools 81
- Chapter 7 83
- Unpacking the main unit 84
- To install the patch panel 87
- To install the WFC 92
- Attach feet here 93
- Chapter 8 97
- Unpacking the expansion unit 98
- To set GASM dip switches 100
- To set GATM dip switches 101
- To install an MBM 102
- Next step 103
- Chapter 9 105
- Connecting the expansion unit 106
- To connect an expansion unit 107
- Connecting the power supply 108
- Figure 51 Connect a UPS 109
- Wiring warnings 111
- G4x16/G8x16 114
- G8x16 MBMs 115
- Music source specifications 117
- Figure 52 Music source jack 118
- Chapter 10 121
- Installing IP phones 122
- Chapter 11 123
- Installing the ATA2 124
- To connect the ATA2 125
- Mounting the ATA2 125
- To mount the ATA2 on a wall 125
- Figure 57 ATA2 back view 126
- Mounting keyhole slots 126
- Configuring the ATA2 127
- Chapter 12 129
- Initial parameters overview 130
- Startup parameters overview 131
- Chapter 13 133
- To enter the keycodes 134
- To configure the IP address 135
- To configure the modem 135
- To select the region 136
- To initialize voice mail 136
- Chapter 14 139
- Prerequisites 140
- Accessing the BCM50 system 140
- To enter a keycode 141
- To configure IP Phones 145
- To configure SNMP settings 146
- To create user accounts 148
- Chapter 15 151
- Startup Profile requirements 152
- Configuring basic parameters 153
- Chapter 16 157
- To configure the MBM(s) 158
- Configuring modem settings 159
- Checking for software updates 159
- Configuring voice mail 159
- Customizing security policies 160
- Performing a backup 160
- Chapter 17 161
- Chapter 18 167
- To troubleshoot the main unit 168
- To test the expansion unit 168
- To test the MBM 169
- To test a station MBM 169
- To test a trunk MBM 169
- Reset to factory settings 171
- Activate the reset feature 172
- Table 31 Level 1 reset 174
- Table 32 Level 2 reset 174
- Chapter 19 175
- To shut down the system 176
- Chapter 20 177
- Removing the power supply 178
- Connect the new power supply 178
- Chapter 21 181
- Removing the main unit 182
- Installing the new main unit 183
- To connect the cables 184
- Chapter 22 185
- To remove the MBM 186
- To insert the new MBM 187
- Chapter 23 189
- Disconnecting the cables 190
- Removing the expansion unit 190
- Removing the MBM 192
- Chapter 24 195
- Special tools 196
- Opening the main unit case 196
- To open the main unit case 197
- To remove the hard disk 199
- To remove the fan 200
- Inserting the new component 201
- To insert the new hard disk 202
- Fan cable cutouts 203
- Fan cable clips 203
- To insert the new fan 204
- To insert the new router card 205
- Closing the main unit case 206
- Installing the main unit 207
- Connecting the cables 207
- Appendix A 209
- Appendix B 213
- Table 35 BRI line numbering 214
- Appendix C 215
- Table 36 LAN port wiring 216
- Appendix D 217
- Appendix E 219
- Appendix F 221
- Appendix G 223
- Appendix H 225
- Appendix I 227
- Appendix J 231
- Appendix K 235
- (Sheet 2 of 2) 236
- (Sheet 1 of 2) 237
- (Sheet 2 of 2) 238
- Appendix L 239
- Appendix M 243
- Appendix N 245
- Digital interfaces 246
- Tones and cadences 247
- • Reorder, 1 kHz on page 253 248
- Functionality Attribute 257
- Market profile 257
- Russia South Africa 265
- Analog Trunk parameters 270
- GASM8 parameters 276
- GASI parameters 279
- Ω 600 Ω 600 Ω 600 Ω 600 Ω 280
- ATA2 parameters 281
- ATA2 DR7 283
- Voicemail 284
- ISDN line services 287
- Trunk Types Description 289
- Numerics 291
Related products and manuals for Routers Avaya BCM50
Routers Avaya 1600 Series User Manual
(100 pages)
(100 pages)
Routers Avaya BCM50e User Manual
(441 pages)
(441 pages)
Routers Avaya BCM50 User Manual
(28 pages)
(28 pages)
Routers Avaya X.25 User Manual
(10 pages)
(10 pages)
Routers Avaya BCM50a User Manual
(315 pages)
(315 pages)
Routers Avaya BCM50 User Manual
(22 pages)
(22 pages)
Routers Avaya BayRS, BCC, and Site Manager Software Version 15.3.0.0 Fixed Anomalies User Manual
(8 pages)
(8 pages)
Routers Avaya T1/FT1 User Manual
(38 pages)
(38 pages)
Routers Avaya BayStack ARN Routers User Manual
(162 pages)
(162 pages)
Routers Avaya (115197-A User Manual
(6 pages)
(6 pages)
Routers Avaya BCM50 User Manual
(46 pages)
(46 pages)
Routers Avaya BayStack ARN Routers User Manual
(160 pages)
(160 pages)
Routers Avaya BCM50 User Manual
(46 pages)
(46 pages)
© 2020, manymanuals.com. All rights reserved. | 1.461 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals