Avaya 1140E User Manual Page 50
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
50 Configure the provisioning server
•
DELAY_WARN [xx] is the threshold to give warning on Excessive
Delay. The default is 150ms.
— xx - any integer value that is 1/65536 of a second.
•
DELAY_EXCE [xx] is the threshold to report unacceptable Excessive
Delay. The default is 175ms.
— xx - any integer value that is 1/65536 of a second.
•
SESSION_RPT_EN [YES | NO] is used to enable or disable per iodic
VQMon session repor ts. The default is disabled.
— YES - enables periodic VQMon session reports.
— NO - disables periodic VQMon session reports.
•
SESSION_RPT_INT [xx] is used to specify the interval for the periodic
VQMon session report in seconds. The default is 60 seconds.
— xx - the value in seconds.
System commands
•
ADMIN_PASSWORD [password] is used to change the default
administrator password of the IP Phone 1140E that is used for unlocking
network menus. The default is 26567*738.
— password - the administrator password.
Create the Dialing Plan file on the provisioning server
A dialing plan essentially describes the number and pattern of digits that
a user dials to reach a particular telephone number. Access codes, area
codes, specialized codes, and combinations of the number of digits dialed
are all part of a dialing plan.
The purpose of the dialing plan is so that the end user does not have to
press the send or pound key (#) to have the IP Phone 1140E with SIP
Firmware send the initial message to start the call.
Dialing a telephone number on an IP Phone that supports SIP can be
different than dialing a number from a traditional telephone. SIP signaling
is communicated through a SIP URI to get to the far end. For example,
you can key in the SIP address, jsmith@yourcompany.com to reach John
Smith. When the IP Phone 1140E with SIP Firmware receives this address,
the dialing plan is bypassed and the IP Phone 1140E simply uses the
SIP URI to send a SIP INVITE to jsmith@yourcompany.com (INVITE sip:
jsmith@yourcompany.com).
SIP Fir mware Release 1.1 for IP Phone 1140E Administration
NN43113-300 02.05 Standard
27 May 2008
Copyright © 2008, Nortel Networks
.
- Phone 1140E Administration 1
- Contents 3
- Index 127 5
- 6 Contents 6
- New in this release 7
- 8 New in this release 8
- How to Get Help 9
- 10 How to Get Help 10
- Introduction to this guide 11
- Related publications 13
- 14 Introduction to this guide 14
- Overview 15
- Related documentation 16
- Installation overview 17
- 18 Overview 18
- Figure 2 18
- Introduction 19 19
- Figure 3 19
- Supported SIP proxy servers 20
- Before installation 21
- Preinstallation 23 23
- 24 Before installation 24
- How provisioning works 25
- Procedure 3 26
- Figure 4 27
- Sample provisioning file 27
- IP Phone 1140E 30
- Device configuration commands 34
- ATTENTION 36
- Feature configuration commands 36
- QoS and ToS commands 44
- Tone configuration commands 45
- NAT configuration commands 47
- VQMon configuration commands 48
- System commands 50
- Dialing function description 52
- Dialing plan 52
- Figure 7 53
- Figure 8 53
- Figure 9 54
- Figure 10 55
- DRegex rules 55
- Downloadable WAV files 56
- Configure the DHCP server 57
- Full DHCP mode 58
- SIP IP Phone class identifier 59
- DHCP VLAN Auto Discovery 61
- 62 Configure the DHCP server 62
- Procedure 4 63
- Installing the IP Phone 1140E 63
- Figure 11 65
- IP Phone 1140E connections 65
- 1140E firmware 67
- Procedure 6 68
- Procedure 7 69
- 3. [FW] Finished 77
- Voice Quality Monitoring 79
- Server set-up 80
- How VQMon works 80
- Introduction 81
- Authorization 83
- Device ID 83
- Password 83
- NO DHCP mode 83
- Net Mask 84
- Voice VLAN 84
- VLAN Filter 85
- Disable PC Port 85
- Data VLAN 86
- PC-Port Untag all 86
- Ignore GARP 87
- Provisioning 87
- NAT Traversal 88
- PVQMon IP 88
- Configure the device settings 89
- STUN S2 IP: 96
- (Single Call Arrangement) 97
- Privacy access codes 98
- Location information 99
- Dialing plan configuration 100
- Characteristics of E911 calls 100
- IP Phone 1140E restrictions 101
- NN43113-300 02.05 Standard 102
- 27 May 2008 102
- NAT firewall traversal 103
- 104 NAT firewall traversal 104
- Three-port switch and VLAN 105
- Phone 1140E 109
- SIP responses 110
- Default error handling 115
- SIP header fields 115
- SDP and Call Hold 119
- Transport layer protocols 119
- SIP security authentication 119
- SIP DTMF Digit transport 120
- Supported subscriptions 120
- Supported instant messaging 120
- Nortel unencrypted Yes 121
- Nortel encrypted Yes 121
- Procedure 14 123
- Reloading UNIStim Firmware 123
- IP Phone 1140E diagnostics 124
- Symbols/Numerics 127
- 128 Index 128
- Index 129 129
- 130 Index 130
Related products and manuals for IP phones Avaya 1140E
IP phones Avaya 1110 User's Guide
(30 pages)
(30 pages)
IP phones Avaya BCM Call Center User Manual
(138 pages)
(138 pages)
IP phones Avaya 0604D9F User Manual
(8 pages)
(8 pages)
IP phones Avaya R4.3 User Manual
(376 pages)
(376 pages)
IP phones Avaya LAN CTE Configuration Guide
(30 pages)
(30 pages)
IP phones Avaya VPNremote Phone User Manual
(25 pages)
(25 pages)
IP phones Avaya 1165E User's Guide
(376 pages)
(376 pages)
IP phones Avaya IP Phone 2001 User's Guide
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 0.477 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals