Avaya 1140E User Manual Page 51
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Create the Dialing Plan file on the provisioning server 51
Entering a SIP URI address, however, is inconvenient for an IP Phone with
SIP Firmware unless a USB keyboard is attached. Also, the user must
explicitly press the send key (or use some method to indicate the end of the
URI) to indicate the completion of the SIP address. This is not something
that the user is accustomed to in a traditional PBX environment.
The alternative is to use a URI where numbers are used to reach the
far end. Using different access codes, the IP Phone with SIP Firmware
translates the digits entered into something that the server can understand
and remaps the number entered into different URIs. Some of the numbers
are mapped as intercom calls, some numbers are mapped as local Public
Switched Telephone Network (PSTN) calls, and some numbers are mapped
as public long-distant calls.
The issue is that until the IP Phone itself can determine the type of call, no
SIP INVITE message is sent. This is where the dialing plan comes into
effect. The call type is determined by the dialing plan. Based on the rules
defined in the dialing plan, once a match has been identified, the IP Phone
1140E with SIP Firmware sends the invite without the need to press the
send key. This behavior closely matches the traditional PBX operation.
The IP Phone 1140E with SIP Firmware design places no restriction in
the format of the SIP URI. The dialing plan is a scheme to match the user
experience with traditional PBX operation. It does not restrict the type of
URI that the user can use.
The IP Phone 1140E with SIP Firmware uses a dialing plan to recognize a
call as an emergency call when it sends an INVITE. The dialing plan can
have multiple emergency numbers. See the chapter "Emergency 911 -
Operator control of disconnect" (page 99) for information on the handling of
Emergency 911 calls by the IP Phone 1140E with SIP firmware.
The following is an example of a dialing plan.
SIP Fir mware Release 1.1 for IP Phone 1140E Administration
NN43113-300 02.05 Standard
27 May 2008
Copyright © 2008, Nortel Networks
.
- Phone 1140E Administration 1
- Contents 3
- Index 127 5
- 6 Contents 6
- New in this release 7
- 8 New in this release 8
- How to Get Help 9
- 10 How to Get Help 10
- Introduction to this guide 11
- Related publications 13
- 14 Introduction to this guide 14
- Overview 15
- Related documentation 16
- Installation overview 17
- 18 Overview 18
- Figure 2 18
- Introduction 19 19
- Figure 3 19
- Supported SIP proxy servers 20
- Before installation 21
- Preinstallation 23 23
- 24 Before installation 24
- How provisioning works 25
- Procedure 3 26
- Figure 4 27
- Sample provisioning file 27
- IP Phone 1140E 30
- Device configuration commands 34
- ATTENTION 36
- Feature configuration commands 36
- QoS and ToS commands 44
- Tone configuration commands 45
- NAT configuration commands 47
- VQMon configuration commands 48
- System commands 50
- Dialing function description 52
- Dialing plan 52
- Figure 7 53
- Figure 8 53
- Figure 9 54
- Figure 10 55
- DRegex rules 55
- Downloadable WAV files 56
- Configure the DHCP server 57
- Full DHCP mode 58
- SIP IP Phone class identifier 59
- DHCP VLAN Auto Discovery 61
- 62 Configure the DHCP server 62
- Procedure 4 63
- Installing the IP Phone 1140E 63
- Figure 11 65
- IP Phone 1140E connections 65
- 1140E firmware 67
- Procedure 6 68
- Procedure 7 69
- 3. [FW] Finished 77
- Voice Quality Monitoring 79
- Server set-up 80
- How VQMon works 80
- Introduction 81
- Authorization 83
- Device ID 83
- Password 83
- NO DHCP mode 83
- Net Mask 84
- Voice VLAN 84
- VLAN Filter 85
- Disable PC Port 85
- Data VLAN 86
- PC-Port Untag all 86
- Ignore GARP 87
- Provisioning 87
- NAT Traversal 88
- PVQMon IP 88
- Configure the device settings 89
- STUN S2 IP: 96
- (Single Call Arrangement) 97
- Privacy access codes 98
- Location information 99
- Dialing plan configuration 100
- Characteristics of E911 calls 100
- IP Phone 1140E restrictions 101
- NN43113-300 02.05 Standard 102
- 27 May 2008 102
- NAT firewall traversal 103
- 104 NAT firewall traversal 104
- Three-port switch and VLAN 105
- Phone 1140E 109
- SIP responses 110
- Default error handling 115
- SIP header fields 115
- SDP and Call Hold 119
- Transport layer protocols 119
- SIP security authentication 119
- SIP DTMF Digit transport 120
- Supported subscriptions 120
- Supported instant messaging 120
- Nortel unencrypted Yes 121
- Nortel encrypted Yes 121
- Procedure 14 123
- Reloading UNIStim Firmware 123
- IP Phone 1140E diagnostics 124
- Symbols/Numerics 127
- 128 Index 128
- Index 129 129
- 130 Index 130
Related products and manuals for IP phones Avaya 1140E
IP phones Avaya 1110 User's Guide
(30 pages)
(30 pages)
IP phones Avaya BCM Call Center User Manual
(138 pages)
(138 pages)
IP phones Avaya 0604D9F User Manual
(8 pages)
(8 pages)
IP phones Avaya R4.3 User Manual
(376 pages)
(376 pages)
IP phones Avaya LAN CTE Configuration Guide
(30 pages)
(30 pages)
IP phones Avaya VPNremote Phone User Manual
(25 pages)
(25 pages)
IP phones Avaya 1165E User's Guide
(376 pages)
(376 pages)
IP phones Avaya IP Phone 2001 User's Guide
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 1.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals